The article below relating to A Step-by-Step Guide to Installing a Bathtub is definitely engaging. Read it yourself and see what you think about it.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is easily accessible, the job can move speedily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list should consist of the following:
Preparing for the Setup
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the restricted access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the needed position. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the bath tub and also examine the overflow outlet and the typical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub should wait till the bath tub has been used at the very least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, creating the water to permeate the wall surface in between the bathroom and the tiling, causing issues with moisture and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I stumbled upon that content on How to Install a Bathtub when doing a search on the web. Sharing is caring. You won't know, you will be helping someone out. I praise you for your time. Visit again soon.
Instant Quote